This is a very time consuming project and I am extra limited because the fabric is black and I avoid sewing black fabrics at night, hence my progress has been so slow. Up to this point I’ve made the buttonholes (the welts were hand sewn in place), sewn all the body’s vertical seams (I left the shoulder seams open), tacked down the SAs and I started hand sewing the satin tape to the waist of the coat. The main reasons for all this hand sewing are: the presser foot could flat down the pile when sewing on the right side of the fabric and avoiding the slide effect when joining two layers when at least one has pile (sewing straight is very difficult because of this sliding effect). I could minor this problem by extra hand basting but I’d risk damaging the satin tape. Hand sewing provides more control and the result is much neater; the only disadvantage is that it takes extra time to get done.
Today I will show you the buttonholes; I used the “window” method, explained in a previous article at my blog (read it here). The only difference is that I’ve hand sewn the welts on instead of topstitching them.
The window method always uses a patch to make the “window”, a small rectangle of sheer fabric on the same color as the fashion fabric. It is placed on top of the buttonhole marked set place on the right side. Then a rectangle (the size of the finished buttonhole) is stitched, using a short stitch setting, and then it’s cut (both patch and fabric). The patch fabric is slipped through the resulting hole to the wrong side of the jacket/coat front, and pressed (see the link to the tutorial provided above for more details and pictures). I used black silk organza for the patch, and the resulting “window” is this (right and wrong side):
After stitching both welts together using a long stitch/loose tension setting, I made a few long running stitches using contrasting thread (basting cotton in this case) so I could see the two welt junction and better center it on the buttonhole window:
In the following picture you can see the process of hand sewing the welts to the buttonhole window (take extra care so each stitch goes through all the fabric layers so the resulting welt is sturdy).
This is how it looks on the wrong side; the canvas will have slightly bigger cut out rectangles at the place of the buttonholes and the allowances you see in the picture will pass through those rectangles when the hymo is set in place on the right front piece. These allowances must be trimmed and graded, and finally tacked down to the hymo. I will share some pictures when I get there.
This is how the buttonhole looks on the right side:
In the meanwhile I’ve started hand sewing the satin tapes around the waist of the coat. I will share pictures when I’m done!
Today I will show you the buttonholes; I used the “window” method, explained in a previous article at my blog (read it here). The only difference is that I’ve hand sewn the welts on instead of topstitching them.
The window method always uses a patch to make the “window”, a small rectangle of sheer fabric on the same color as the fashion fabric. It is placed on top of the buttonhole marked set place on the right side. Then a rectangle (the size of the finished buttonhole) is stitched, using a short stitch setting, and then it’s cut (both patch and fabric). The patch fabric is slipped through the resulting hole to the wrong side of the jacket/coat front, and pressed (see the link to the tutorial provided above for more details and pictures). I used black silk organza for the patch, and the resulting “window” is this (right and wrong side):
After stitching both welts together using a long stitch/loose tension setting, I made a few long running stitches using contrasting thread (basting cotton in this case) so I could see the two welt junction and better center it on the buttonhole window:
In the following picture you can see the process of hand sewing the welts to the buttonhole window (take extra care so each stitch goes through all the fabric layers so the resulting welt is sturdy).
This is how it looks on the wrong side; the canvas will have slightly bigger cut out rectangles at the place of the buttonholes and the allowances you see in the picture will pass through those rectangles when the hymo is set in place on the right front piece. These allowances must be trimmed and graded, and finally tacked down to the hymo. I will share some pictures when I get there.
This is how the buttonhole looks on the right side:
In the meanwhile I’ve started hand sewing the satin tapes around the waist of the coat. I will share pictures when I’m done!
1 comment:
Tany,Bound buttonholes are my very favorite to make. Your step by step is great.Your buttonholes look wonderful, very professional and well done. I can appreciate they are time consuming to make but you still take the time to take pictures as you go. Very thoughtful. Thank you :)
Post a Comment